Warning: file_put_contents(/www/wwwroot/www.1000114.com/index/temp_block/www.fr-p.com/bpsuuesatmhsedhtml.php): failed to open stream: No space left on device in /www/wwwroot/www.1000114.com/index.php on line 131
宝贝请负责全文免费阅读宝贝请负责全文免费阅读,小泽玛丽亚等人觉得很赞小泽玛丽亚等人觉得很赞

宝贝请负责全文免费阅读宝贝请负责全文免费阅读,小泽玛丽亚等人觉得很赞小泽玛丽亚等人觉得很赞

发布日期:2021年04月22日
设为首页 | 加入收藏 | 联系我们
宝贝请负责全文免费阅读宝贝请负责全文免费阅读,小泽玛丽亚等人觉得很赞小泽玛丽亚等人觉得很赞
# #
帕森斯(张家口)工业技术有限责任公司
地 址:张家口高新技术产业开发区通泰大街6号
电 话:0313-5953535 5953505
网 址:www.parsonszjk.com
邮 箱:sales@parsonszjk.com
邮 编:075000
宝贝请负责全文免费阅读宝贝请负责全文免费阅读,小泽玛丽亚等人觉得很赞小泽玛丽亚等人觉得很赞
 
 
II型液压切链器

 我公司生产的液压切链器消化和吸收国内外先进技术,转为切断各种圆环链条的链环设计和制造。剪切链条直径从∅22到∅48。其主要结构由液压切断器、手动油泵(液压泵站)、换向增压器和高压油管组成,工作介质为液压油或乳化液。按工作介质不同,可分为I型液压切链器和II型液压切链器。

Hydraulic chain cutter designed  is manufactured by GIT was deployed to cut the chain in 22-48mm.It invloved the up to date technology home and abroad and classified into two types (Type 1 and Type 11)accroding to the work fluid .The whole set is an assembly of hydraulic chain cutter,hand oil pump (oil pump station),reversing supercharger and high pressure oil hose with the work fluid either hydraulic press oil or emulsifiec mixture.

切链器技术参数

II型切链器由液压切断器、液压泵站、换向增压器和高压管路组成。

The whole set comprise hydraulic chain cutter,electric-oil pump,reversing supercharger and high pressure oil hose.

主要特点:

1、结构简单,操作方便;

2、具有独特的安全措施,工作过程安全可靠;

3、动作迅速,提高工作效率;

4、工作介质:乳化液。

Main feature

1、simple structure ,easy operation

2、Special security method ,safe work process

3、Fast speed increase work ef

4、Work fluid :hydraulic press oil or emulsified mixture

操作方法:

1、井下液压泵站直接提供动力,将液压泵站和增压器、液压切断器用高压管连接好,启动泵站,人工操纵增压器转向手柄,直到将链环切断。

2、将增压器上的手动泄压阀打开,弹簧装置使液压缸回复原位,准备下一次切割。

Operation Instruction:

1.Underground oil pump directly offer power,then connect the oil pump,reversing supercharger and hydraulic chain cutter with high pressure oil hose.Start the oil pump ,move the lever of hydraulic directional control value of the supercharger until the chain is cut.

2.Move the lever of hydraulic dirctional control value back to the discharge position,the spring the device will make the hydraulic cylinder return to its original position and repeat for next operation.

注意事项:

宝贝请负责全文免费阅读宝贝请负责全文免费阅读,小泽玛丽亚等人觉得很赞小泽玛丽亚等人觉得很赞

1、使用前,需检查刀头固定情况,是否有算坏;

2、高压胶管端头和管接头必须保持清洁,各密封件必须完好;

3、使用润滑脂对切断刃进行润滑,并除去链环表面污物,垂直放置在切断刃中央;

4、切记用重物敲击刀刃外漏部分;

5、保证实际工作压力不超过额定压力。

1、Check if the cutting head fitted well or any broken parts appears before operation.

2、The hose socket and adaptor should be clean.The seal parts should be in good condition.

3、Grease and lubricate the cutting edge,clean off the dirt in the surface of the link ,then posite the link agasint the both end of the cutter in right angle .

4、Do not knock the edges of the cutter with heavy items.

5、Make sure the actual working pressure not excess rated pressure.